We have stumbled on the article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and believe it made sense to discuss it with you over here.
Setting up a bathtub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is easily obtainable, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and position the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old tub and embeded in the new one. See to it you have certified yourself for the job as well as are comfortable trying it. Rather than employing a specialist to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will aid you install a new bath tub in your restroom if you have actually already purchased a brand-new tub as well as do not require to change the setup of your previous water supply pipes.
Your devices and material list need to consist of the following:
Getting ready for the Installment
To start with, the supporting structure provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic due to the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Using both wood boards under its feet, position the tub in the required setting. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four small factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible tap port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water and examine all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the bath tub and likewise examine the overflow outlet and also the typical outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making sure that the washers remain in area in between the tap as well as the sink. Safeguard the tap in position with the maker given backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind needs to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a stiff seal, causing the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in complications with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that editorial about A Step-by-Step Guide to Installing a Bathtub from an associate on a different web blog. In case you appreciated our blog posting please do not forget to pass it around. Thanks a lot for taking the time to read it.
More Details